In printing, the paper collecting system is related to the paper feeding system, positioning system, paper conveying system, water conveying ink system, paper collecting system, etc. How to solve the problem of uneven collection? As a Jinan album printing company, we summarize the following aspects:

　　1. 本文系统

　　1. This system

　　输纸系统包括振荡装置、输纸辊和链条。其标准状态如下:

　　The paper conveying system includes an oscillating device, a paper conveying roller and a chain. The standard status is as follows:

　　摆动装置。当凸轮在更小的摆动面上时，弹簧的张力略大，此时滚子与凸轮之间要保持20根钢丝的间隙。摆动装置与预卷纸辊连接时，牙垫之间的水平间距约为20根导线。

　　Swinging device. When the cam is on the minimum swing surface, the tension of the spring is slightly larger. At this time, the gap between the roller and the cam should be kept at 20 steel wires. When the swing device is connected with the pre roll roll, the horizontal space between the tooth pads is about 20 wires.

　　纸张传输系统功能单元。刁里的纸大约是2-4mm。雕的角度应大于450度。刁的前端应该是水平的。

　　Paper transfer system function unit. The paper in diaoli is about 2-4mm. The angle of carving shall be greater than 450 degrees. Diao's front end should be horizontal.

　　2. 给水系统

　　2. Water supply system

　　为了保证纸张的正常稳定，我们必须把握好以下几点:压纸脚——一定要平衡。纸堆正面低于整洁的纸块2 ~ 3mm，吸纸嘴应吸纸到位，放纸应尽快退回。吸纸嘴在吸纸状态下应降点，运转平稳。压脚、分离吸纸嘴、通过吸纸嘴与导纸辊的时间协调应处于标准状态。

　　In order to ensure the normal stability of paper, we must grasp the following points: presser foot - must be balanced. The front side of the paper pile is 2 ~ 3mm lower than the clean paper block, the paper suction nozzle should be in place, and the paper should be returned as soon as possible. The paper suction nozzle shall be lowered to the lowest point in the paper suction state, and the operation shall be stable. The time coordination of presser foot, separating the paper suction nozzle and passing the paper suction nozzle with the first paper guide roller shall be in the standard state.

　　3.定位系统(GPS)

　　3. Positioning system (GPS)

　　定位系统包括前压力计、点压力计和侧压力计。他们的标准如下:

　　The positioning system includes front pressure gauge, point pressure gauge and side pressure gauge. Their criteria are as follows:

　　1)规则之前。两个前规在同一水平线上，这样每个单位的纸张传输系统之间的纸张倾角在2 ~ 4mm的范围内。此时前规是固定的，不要随意移动。

　　1) Before the rules. The two front gauges are on the same horizontal line, so that the paper inclination between each unit's paper transmission system is within the range of 2-4mm. At this time, the front gauge is fixed, do not move at will.

　　(2)电动牙。前量规下降，纸放到位。此时，电牙前端与纸张前端之间的距离约为1mm。

　　(2) Electric teeth. Lower the front gauge and put the paper in place. At this time, the distance between the front end of the electric tooth and the front end of the paper is about 1mm.

　　(3)侧规。振荡器只是用牙齿蘸着纸，而侧规只是把纸压起。此时，纸张应处于两者的联合控制下，且所提高的高度应大于450。

　　(3) side gauge. The oscillator just dips the paper with its teeth, while the side gauge just presses the paper up. At this time, the paper should be under the joint control of the two, and the maximum height raised should be greater than 450.

　　4. 冲压系统

　　4. Stamping system

　　将印版滚筒和橡皮布滚筒洗净，压入熔丝后，测量被压熔丝的厚度，两辊之间的压力厚度。

　　Clean the plate cylinder and blanket cylinder, press in the fuse, and measure the thickness of the pressed fuse and the pressure thickness between the two rollers.

　　5. 纸系统

　　5. paper system

　　(1)制版前后，前后左右的位置和印刷规格要对号;链条刚放纸，边纸板刚搬出来;(3)吸轮吸纸后应稳定;后吸轮与下吸风口的间隙约为20根导线;(5)开球角度应在20左右;风轮的吸力从中间向两边递减，以此类推。

　　(1) Before and after plate making, the front and rear positions and printing specifications should be numbered; the chain just put paper, and the edge cardboard just moved out; (3) the suction wheel should be stable after absorbing paper; the gap between the rear suction wheel and the lower suction port is about 20 wires; (5) the ball opening angle should be about 20; the suction force of the wind wheel decreases from the middle to both sides, and so on.

　　6. 给水油墨系统

　　6. Water supply ink system

　　(1)正常印刷时，墨辊上的油墨均匀而不大，细听时油墨光滑无声，印品较厚。

　　(1) In normal printing, the ink on the ink roller is uniform but not large. When listening carefully, the ink is smooth and silent, and the printed matter is thick.

　　要把握好水分，不要弄脏了印品，而且印件满厚，越小越好。

　　To grasp the moisture, do not dirty the print, and print full thickness, the smaller the better.

　　以上是济南画册印刷厂家为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：http://www.jindingyinshua.comThe above is the related content introduced by Jinan album printing factory. If you want to know more, please visit the website: http://www.jingyinshua.com