手提袋是很多产品或类包装会配的一个包装部件，有了手提袋会让人感觉整个产品更完整，那如何在设计阶段做一个效果图让决策者提前感受下整个产品的终效果，而决定是否为这个产品做一个手提袋。
Handbags are a packaging component of many products or high-end packaging. With handbags, people will feel the whole product more complete. How to make an effect map at the design stage so that decision makers can feel the final effect of the whole product in advance, and decide whether to make a handbag for this product.
对于很多企业来说商业所用到的礼品，文件，书籍又或者自身产品都需要手提袋来盛放。手提袋可谓相当的适用，单一造价也不高。但是手提袋印刷在质量和品质上要求还是非常高，因此此类印品比较直观展示公司相关信息，消费者直观关注的正是我们手提袋印刷的内容，因此在印刷手袋的过程可能遇到的问题如下：
For many businesses, gifts, documents, books or their own products used in business need handbags to store. Handbags are quite suitable, and the single cost is not high. However, the quality and quality requirements of handbag printing are still very high. Therefore, this kind of printing can display the company's relevant information more intuitively. The most intuitive concern of consumers is the content of our handbag printing. Therefore, the problems that may be encountered in the process of printing handbags are as follows:
一、手提袋印刷采用的水墨都为纯水性体系，不要将水墨与醇性墨和溶剂型油墨混合使用或在墨中加入有机溶剂，以免导致印刷质量问题。
First, the ink used in handbag printing is pure water-based system. Do not mix the ink with alcohol ink and solvent-based ink or add organic solvents in the ink, so as to avoid printing quality problems.
二、水墨的印刷适性受印刷条件、承印物的表面特性、环境温湿度；水墨存放时间长短等客观条件的影响，因此在使用水墨时，需要用一些助剂对水墨做细微调整以获得佳印刷效果。
Secondly, the printability of ink is affected by the objective conditions such as printing conditions, the surface characteristics of the substrate, environmental temperature and humidity, and the length of storage time of ink. Therefore, when using ink, it is necessary to use some additives to fine-tune ink to obtain the best printing effect.
三、残留在印刷设备上墨水尽量在未干燥前用清水冲洗干净，无法用清水洗净的墨可用清洗剂进行清洗。
3. Remaining ink on printing equipment should be washed with clean water as far as possible before drying. Inks that cannot be washed with clean water can be cleaned with detergent.
四、印刷过程中由于水的挥发作用，会导致水墨粘度升高和PH值下降，PH值应控制在8．5—9．5之间，若超出此范围，可用PH稳定剂进行调节，保持粘度和PH值的稳定。
Fourth, the volatilization of water in printing process will lead to the increase of ink viscosity and the decrease of PH value. PH value should be controlled between 8.5 and 9.5. If it exceeds this range, PH stabilizer can be used to adjust it to maintain the stability of viscosity and PH value.
五、印刷剩余的墨水可以收回原装桶里并将盖子盖严实，下次可重复使用。
5. The remaining ink from printing can be retrieved from the original barrel and tightly covered. It can be reused next time.
六、水墨适宜的储存温度是5℃—50℃摄氏度。
6. The optimum storage temperature for ink is 5-50 degrees Celsius.
七．稀释剂：用于降低水墨的粘度。用量在3％以内不会降低水墨的颜色深度，并可保持水墨的PH值不变，加入较多的稀释剂或使用硬度高的自来水稀释会导致气泡的产生，可同时加入消泡剂进行消泡。稀释剂应边搅拌边缓慢加入，以防粘度过低。
Dilutants: Used to reduce the viscosity of ink. When the dosage is less than 3%, the color depth of the ink will not be reduced, and the PH value of the ink will remain unchanged. Adding more diluents or using high hardness tap water to dilute will lead to the formation of bubbles, and defoamer can be added to defoam at the same time. The diluent should be added slowly while stirring to avoid low viscosity.
八.慢干剂：用于降低水墨的干燥速度，用量在10％以内。
8. Slow drying agent: used to reduce the drying speed of ink, dosage less than 10%.
More information about Jinan handbag can be consulted by clicking on our official website: http://www.jindingyinshua.com/
